The M113-series FOV’s heater box-equipped engine, NSN 2815-01-248-7644, is being phased out through attrition. It’s replacement is the glow plug-equipped engine, NSN 2815-01-412-2715.
If you have an M113 that’s due for an engine replacement, order the new version. Keep in mind that you’ll need the glow-plug conversion kit, NSN 2815-01-653-9437. The kit upgrades the electrical system so it can accept the new engine.
You’ll find the instructions for installing the conversion kit in TM 9-2350-277-13&P in IETM EM 0321 (Oct 14).
Questions? Contact Christopher Faiola at DSN 786-8291, (586) 282-8291, or email:
or Floyd Perry at DSN 786-8290, (586) 282-8290, or email:
or Richard Darling DSN 786-2517, (586) 282-2517, or email:
GCSS-Army Turn-in Credit
GCSS-Army has its own set of document numbers. Once the customer is issued a glow plug-equipped engine, NSN 2815-01-412-2715, a ZRL (return delivery to SSA) purchase request document is created. The ZRL document number is eligible for credit for 180 days.
The customer then turns in the heater box-equipped engine, NSN 2815-01-248-7644, with a ZXS (excess requisition) document since the return has no corresponding issue. The ZXS document will be assigned a return advice code (RAC) of 1W.
The SSA will need to manually match the -7644 return receipt against the -2717 issue document and manually remove the RAC to allow the system to generate credit. The SSA will also need to manually close the ZRL document so that it doesn’t match to another turn-in receipt.
Note: The issue and return MILSTRIP document numbers will be different.
Operators, it’s no secret that M400W compact-skid loaders have an ongoing problem with battery drain.
Most of these vehicles use the yellow-top Optima batteries. Even though they’re high quality batteries, they can’t stand the constant drain by the loader’s electrical system. The constant discharge leads to sulfated plates. Over time, the Optima battery can no longer be charged and has to be replaced. The end result is way too many dead batteries in these skid loaders. And the cycle continues.
Here are four ways to stop needless battery replacement:
o Start the skid loader weekly and run it for an hour.
o Every other week, plug a charger into the vehicle’s NATO receptacle and fully charge the battery set. The ProHD, NSN 6130-01-500-3401, is an approved charger that comes with the SATS.
o For long-term storage, make sure you disconnect the skid steer loader’s batteries.
o For skid loaders stored outdoors in the motor pool, use a solar charging system, like the Solar Pulse Monitor System, NSN 6130-01-558-5371. It simply plugs into the NATO receptacle and no modifications are needed.
Pilots, having the right radio in your Lakota rotorcraft is the difference between communicating and not communicating.
The bad news is that some RT-5000 radios meant for Kiowa OH-58A/C models have been installed on the Lakota UH-72A models. The wrong radio sets were moved into unit avionic stocks and used in Lakotas as line replaceable units (LRUs).
Both airframes use RT-5000, remote-mount, multi-band AM/FM transceiver radios. The version used for OH-58A/C Kiowas does not allow for digital transmission and reception of the same frequency signals like the RT-5000 approved for the Lakota.
If your UH-72A’s radio isn’t operating properly, eyeball the part number (PN) and cross check that PN against the proper supplemental type certificate (STC) for the correct Mission Equipment Package (MEP) of the rotorcraft.
Lakotas operating in a security and support (S&S) MEP, need the RT-5000s with PN 400-105525-6011 for comm #4, and PN 400-105525-6111 for comm #5. For Lakotas in a non-S&S MEP configuration, the RT-5000 radio should be PN 400-015525-5111 operating in comm #4.
If you find an unauthorized radio in your Lakota, make the following entry in the aircraft logbook:
“RT-5000 (PN 400-015525-xxxx*) required removal and replacement per aircraft’s STC with correct RT-5000 (PN 400-015525-xxxx*)”
*Ensure the PN(s) reflect the RT-5000 to be removed and the correct PN(s) for the MEP version that is going to be installed.
Got questions about the RT-5000 radio? Contact Keith Stilwell, DSN 645-0797, (256) 955-0797 or email:
Mechanics, aircraft jacks are vital for maintenance on your helicopter. They’ve been around for years and gone through a lot of changes. Some have been put out to pasture while others have been neglected.
Now, that won’t be a problem anymore because we told you on Pages 27-30 of PS 760 (Mar 16), how to maintain your jacked up jacks.
With all the changes, sometimes it’s difficult to determine which jack is used for which aircraft task. No longer. Here’s a list of the maintenance tasks that require jacks and how many to use:
NOTE: These are typical tasks which require the aircraft to be placed on jacks. Please ensure you follow TM 1-1520-Longbow/Apache (IETM) for specific requirements, size, placement, warnings, cautions, and notes for all jacks.
- Jacking aircraft, 3 point, using a tripod jack requires two 5-ton jacks, NSN 1730-00-516-2018, and one 3-ton jack, NSN 1730-00-734-9382. The Fuselage adapter, NSN 1560-01-226-7551, will also be used.
- Jacking aircraft, 2 point, using a tripod jack requires two 5-ton jacks, NSN 1730-00-516-2018. The Fuselage adapter, NSN 1560-01-226-7551, will also be used.
- Jacking tail landing gear using a tripod jack requires one 3-ton jack, NSN 1740-00-734-9382.
- Jacking the main landing gear, 1 point, using an axle jack requires one 5-ton jack, NSN 1740-00-540-2343. Chinook
- Note that Apache is the only helicopter airframe that uses the 5-ton jack, NSN 1730-00-516-2018.
- Jacking an entire Chinook requires two 12-ton jacks, NSN 1730-00-912-3998, and two 10-ton jacks, NSN 1730-00-203-4697. As an alternative method, you can use two 12-ton jacks, NSN 1730-00-912-3998, and one 10-ton jack, NSN 1730-01-563-7046.
- Replacing the forward right- or left-hand gear assembly requires one 10-ton jack, NSN 1730-01-563-7046. However, the aircraft weight must be below 24, 500 pounds.
- Replacing the forward right- or left-hand tire assembly requires one 10-ton jack, NSN 1730-203-4697.
- Replacing the aft right- or left- hand gear assemblies requires one 12-ton jack, NSN 1730-00-912-3998.
- Replacing the aft right- or left- hand tire assembly requires one 12-ton jack, NSN 1730-00-912-3998.
- Weighing aircraft using load cells (3 point) with a max gross weight of 24,500 pounds requires two 12-ton jacks, NSN 1730-00-912-3998, and one 10-ton jack, NSN 1730-01-563-7046.
- Weighing aircraft using load cells (4 point) with a max gross weight of 33,000 pounds requires two 12-ton jacks, NSN 1730-00-912-3998, and two 10-ton jacks, NSN 1730-00-203-4697.
- A/C Model Kiowa Warrior
- Jacking an entire OH-58A/C requires three 12-ton jacks, NSN 1730-00-912-3998.
- D-Model Kiowa Warrior
- Jacking an entire OH-58D requires three 12-ton jacks, NSN 1730-00-912-3998. Black Hawk Aircraft
- NOTE: When a Kiowa is on jacks, use an overhead hoist or cable support to maintain the aircraft. This is done as a safety precaution in the event a strong wind gust blows through the hangar and knocks the Kiowa off the jacks.
- Jacking requires three 12-ton jacks, NSN 1730-00-201-4849.
- Removal and installation of the right- and left-hand landing gear shock strut requires one 12-ton jack, NSN 1730-00-201-4849.
- Jacking the right- and left-hand main landing gear wheel and tire assembly requires one 10-ton jack, NSN 1730-00-203-4697.
- Removal and installation of the tail landing gear shock strut requires one 12-ton jack, NSN 1730-00-201-4849.
- Removal and installation of the tail landing gear wheel and tire assembly requires one 10-ton jack, NSN 1730-00-203-4697.
- Weighing the helicopter using load cells (3 point) requires three 12-ton jacks, NSN 1730-00-201-4849.
- Changing a flat tire or collapsed strut requires one 12-ton jack, NSN 1730-00-201-4849, or one 10-ton jack, NSN 1730-00-912-4697.
- Changing a flat tail tire or collapsed gear strut requires one 12-ton jack, NSN 1730-00-201-4849, and one 10-ton jack, NSN 1730-00-912-4697.
- Lakota Aircraft
- Jacking an entire UH-72A aircraft takes four jacks. The type of jack is not specified, but two 12-ton tripod jacks, NSN 1730-00-912-3998, and two 10-ton landing gear jacks, NSN 1730-00-203-4697, work well.
- Weighing the Lakota requires three jacks. The type of jack is not specified, but one 12-ton tripod jack, NSN 1730-00-912-3998 and two 10-ton landing gear jacks, NSN 1730-00-203-4697 work well.
If your unit uses the M151 spotting scope, NSN 6650-01-504-8456, NSN 6650-01-557-7444 or NSN 6650-01-549-5838, good news! The scope is being upgraded to improve its performance when used with a night vision device. The upgrade includes a grid-based reticle and night vision adapter.
The upgrade will be done by MWO 9-6650-238-50-1. The old spotting scopes will be swapped out at Camp Robinson, Eglin Air Force Base, Ft Benning, Ft Bliss, Ft Bragg, Ft Campbell, Ft Carson, Ft Drum, Ft Hood, Ft Lewis, Ft Polk and Ft Stewart. The swaps will be scheduled through FORSCOM in accordance with AR 750-10. TACOM is managing the MWO.
If your unit isn’t located at one of these posts, the swap will be handled by mail. Contact your local MWO coordinator for instructions. It will take roughly a month for the mail-in swap.
Whether your M151 is being swapped out locally or mailed in, it should be stripped down and contain no down parts. Any parts turned in other than the scope won’t be returned and it will be the unit’s responsibility to replace them.
Questions? Contact Buck Sewell at (586) 282-1333 or email:
or Christopher Kline at (586) 282-1357 or email:
Item 1 of Fig 22 in TM 5-3805-298-24P (Mar 13) lists the 924H wheel loader’s precleaner, NSN 2940-01-068-7108. Replacing it will cost you a bit more than $107.
But what if it’s the cover or body that’s broken? Seems a shame to pay that much when only part of the precleaner is damaged.
Good news! Now you can replace those precleaner parts:
Repairing the precleaner will save you a lot of bucks over the cost of a new precleaner. Make a note until the parts are added to the TM.
Some units are deadlining the M1235A4/A5 MaxxPro Dash ISS MRAP during checks and services. Why? Because they see cracks in the rubber boot cover on the steering gear output shaft that connects to the pitman arm.
Step 3 of Items 15 and 106 in the PMCS tables of TM 9-2355-441-10 says to check the pitman arms for cracks and bends. If the pitman arm is cracked or bent, the vehicle is deadlined.
But this is a case of mistaken identity! This particular check is referring to the pitman arm itself, not the output shaft’s rubber boot.
Cracks or tears in the output shaft boot do not deadline your vehicle. Cracks there have no bearing on the form, fit or function of the pitman arm. The pitman arm has an internal seal to protect it.
For more info, check out TACOM Maintenance Information message 16-046: